| |
DigiTech RP200 Modeling Guitar Processor
Other Functions
Rhythm Trainer
The RP200 includes several sampled drum patterns which are useful for developing a good sense
of timing. Pressing the Rhythm button will enable Rhythm mode and start playback of the drum
loop (except when in Store or Bypass mode). In Rhythm mode, the Parameter 1 knob selects
the drum Pattern, the Parameter 2 knob adjusts the drum Tempo, and the Parameter 3 knob
adjusts the Level of the drum loop. Press the Rhythm button again to stop playback of the drum
loop.
Jam-A-Long
The Jam-A-Long feature allows you to connect a Tape or CD to the RP200, and Jam with your
favorite artists.The signal from your tape or CD player is output through the left,right,and
headphone outputs of the RP200. To use the Jam-A-Long feature, connect the headphone output
of your tape or CD player to the Jam-A-Long Input on the rear panel of the RP200 using an
1/8" stereo cable, and press play on your tape or CD player.
Expression Pedal
The Expression Pedal on the RP200 can be assigned to control the RP200's Volume,Wah,
Whammy™,Ya Ya™, or one of several other parameters in real time with your foot. When a
parameter has been assigned to the Expression Pedal, a programmable minimum and maximum
value can also be assigned.The procedure for assigning a parameter to the Expression Pedal is as
follows:
- Press the Select button until the Expression row has been selected (indicated by the LED
lighting on the Expression row).
- Rotate the Parameter 1 knob until the desired Parameter appears in the Display.Your
choices include:
WAH (Wah) - The Expression Pedal acts as a Wah when the Wah Effect is engaged.
A GAIN (Amp Gain) - Expression Pedal controls the Amp Gain or amount of distortion for
the selected Amp Type.
AMPLVL (Amp Level) - Expression Pedal controls the Volume of the selected Amp Type.
AMOUNT (Amount) - Expression Pedal controls the Amount of the selected Effect Type.
EFFLVL (Effect Level) - Expression Pedal controls the Mix Level of the selected Effect Type.
YAYA (YaYa™) - Expression Pedal acts as a Ya Ya™ Effect when YaYa™ is engaged.
WHAMMY (Whammy™) - Expression Pedal acts as a Whammy™ Pedal when Whammy™ is
engaged.
FBACK (Feedback) - Expression Pedal controls the amount of Delay Feedback.
DLYLVL (Delay Level) - Expression Pedal controls the Mix Level of the selected Delay Type.
DECAY (Decay) - Expression Pedal controls the length of Reverbs Decay time.
REVLVL (Reverb Level) - Expression Pedal controls the Reverbs Mix Level.
VOLPRE (Volume Pre) - Expression Pedal controls the Volume after the Amp Modeling but
before the Effects.
VOLPST (Volume Post) - Expression Pedal controls the Volume at the end of the Effects chain.
- Rotate the Parameter 2 knob to select the minimum value the assigned parameter will reach
with the Expression Pedal in the toe up position (not available when volume is the assigned
parameter).
- Rotate the Parameter 3 knob to select the maximum value the assigned parameter will
reach with the Expression Pedal in the toe down position (not available when volume is the
assigned parameter).
- Store your Expression Pedal assignment to your Preset. See page 13 for more information on
the storing procedure.
Factory Reset
This function resets the RP200 to its original factory settings.This procedure will erase all
custom user Presets, and recalibrate the Expression Pedal.
ATTENTION: Performing this function will erase all user-programmed data.All such data
will be lost forever! Be sure you want to erase the memory and start fresh
before continuing with this procedure.
The procedure for performing a Factory Reset is as follows:
- Disconnect the power supply from the RP200.
- Press and hold the Select button while re-connecting the power to the RP200.
- When the display shows RST ?, release the Select button and press the Store button.
The display will briefly read RESET indicating that the RP200 has reset the original factory
settings.At this point,the RP200 will automatically advance to the Expression Pedal calibration
menu. Follow steps 4 through 7 of the Expression Pedal calibration section.
Expression Pedal Calibration
The Expression Pedal on the RP200 needs to be recalibrated for use after a factory reset has
been performed.This calibration procedure is automatically entered after a factory reset
procedure. In the event the Pedal's calibration fails, or if the Pedal does not function properly, it
can be re-calibrated using the Pedal Calibration procedure.This will not erase the User Presets.
The procedure for Calibrating the Expression Pedal is as follows:
- Disconnect the PS0913B power supply from the power jack on the RP200.
- Press and hold the Up Footswitch while reconnecting the power.
- Continue to hold the Up Footswitch until the Display reads TOE DN.
- Rock the Expression Pedal forward to the toe down position.
- Press either Footswitch and the Display now shows TOE UP.
- Rock the Expression Pedal back to the toe up position.
- Press either Footswitch.The RP200 will return to the last selected Preset and the Expression
Pedal is now calibrated.
Note: If the Display shows ERROR, an error has occurred and steps 4 through 7
should be repeated.
| |
